Page Comparison

Aaron Chan (RIT Student) Akhil Devarapalli (RIT Student) Jonathan Russo (RIT Student) Chloe Clark (RIT Student) 

• Sensor drivers written
• Onboarding

TODO:

•  Onboard new people Aaron Chan (RIT Student)
•  Test SHTC3 - @Sebastian @The Other Other Guy
•  SHTC3 Sensor Module Task
•  Test  ADXL375 - Akhil Devarapalli (RIT Student) @The Other Guy
•  ADXL375 Sensor Module Task 
•  Test BMP390 Aaron Chan (RIT Student) 
•  BMP390 Sensor Module Task - Aaron Chan (RIT Student) 
•  Test MS56701
•  MS56701 Sensor Module Task
•  Test L3GD20H 
•  L3GD20H Sensor Module Task
•  Test LIS3MDL
•  LIS3MDL Sensor Module Task
•  Test LSM6DSL
•  LSM6DSL Sensor Module Task
•  Test MMA8451Q
•  MMA8451Q Sensor Module Task
•  Test W25Q - Aaron Chan (RIT Student) 
•  W25Q Module Tasks
  •  Sensor
  •  Power
  •  Radio
  •  Autopilot
•  Test W5500 
•  W5500 Module Tasks
  •  Sensor
  •  Power
  •  Radio
  •  Autopilot
•  Write RFM95W Drivers - Jonathan Russo (RIT Student) 
•  Write MAX10 GPS Drivers - Jonathan Russo (RIT Student) 
•  Finish ICMP - Chloe Clark (RIT Student) 

Dante Sivo (RIT Student) Jonathan Russo (RIT Student) 

Updates:

• Added ESD to connectors
• Added UART jumpers to GPS and a debug bus 
• Schematic updates "beautified" 
• Board Ready for review

To-Do:

•  Drivers for RFM95W - Jonathan Russo (RIT Student) 
•  Drivers for GPS - Jonathan Russo (RIT Student) 
•  Verify impedance control. Layer Stackup Templated might be wrong - Dante Sivo (RIT Student) 
•  Add JLCPCB Part #'s to parts used - Dante Sivo (RIT Student)
•  Mark mounting holes as DNPs - Dante Sivo (RIT Student) 
•  Schematic Review - Dante Sivo (RIT Student) /w team
•  Layout Review - Dante Sivo (RIT Student) /w team
•  Provide Louis with a proper full quote from JLCPCB - Dante Sivo (RIT Student) 

Updates:

• Design voltage/current sense
• Select passives for most ICs
• Schematic is 60% complete

To-Do:

•  James May (RIT Student) Update Block Diagram to reflect current design
  
•  James May (RIT Student) simulate umbilical switch in LTspice, look at power loss
•  James May (RIT Student) Assemble BOM & include all components
  •  Create BOM file
  •  Add switcher
  •  Add switcher passives
  •  Add umbilical switch components
  •  Add monitoring components
  •  Add monitoring passives
  •  Add microcontroller
  •  Add microcontroller passives
  •  Add WIZnet
    
  •  Add WIZnet passives
  •  Add flash memory
  •  Add flash passives
•  James May (RIT Student) Spec shielded inductors
•  James May (RIT Student) Complete schematic capture
  •  Complete switcher design
  •  5V switcher
  •  3.3V switcher
  •  Backplane connector
    
  •  current measure
  •  voltage measure
  •  WIZnet
  •  Complete battery/umbilical switch design
  •  Battery/umbilical switch
  •  Programming interface
  •  Add microcontroller & logging circuitry (should be roughly identical to other modules)
•  James May (RIT Student) Complete layout
  •  Place components
  •  Calculate power trace widths
  •  Route power traces
  •  Route signal traces
•  James May (RIT Student) Simulate switchers in Webench