fPropulsion

Content

Structures

• Nose Cone (w/ Integrated Coupler)
  • Tip Protector
  • Nose Cone Screws M6 (x6)
• Parachute Bay (Upper Body Tube)
• Booster (Lower Body Tube)
  • Motor Retainer w/ Screws (Attached to Booster)
• Rocket Epoxy
  • Scale
  • Mixing Cups
  • Popsicle Sticks
• 5 Minute Epoxy
• Sandpaper
• 4-40 Shear Pins (>20)
• 3x PVC Rocket Stand 
• Cordless Drill & Battery
• Drill Battery Charger
• Flat Head Screwdrivers
• Phillips Head Screwdrivers
• Drill Bit Set
• Knife
• FOR DISPLAY
  • Extra Bulkhead(s)
    • Weight Reduced
    • Charge Caps
  • Extra Rail Guide
  • Old Boat Tail

Recovery

Content

Payload

Content

Avionics

TAKE PICTURES OF EVERY COMPOSITE ITEM, PACKED AND UNPACKED

• Radio Pelican case Aaron Chan (RIT Student) 
  • (Loose items) 10x HAM radio
  • (Loose items) 12x FRS radio (11x currently. Donovan has his)
  • (Bag) 3x APRS cable
  • (Bag) Antenna bag
  • (Loose item) BAOFENG charger
• Avionics Pelican case Aaron Chan (RIT Student) 
  • (Camo case) 433 MHz Yagi
  • (Loose) Smaller 433 MHz Yagi
  • (Loose) 900 MHz Yagi
  • (Box) Avionics bay box
    • (Loose) Delrin frame
      • 3x Finger Tech screw switches populated
    • (Loose) COTS sled
    • (Loose) Backplane sled
    • (Loose) Big Red Bee bracket
    • (Loose) Backplane battery case
    • (Loose) 2x RRC3 battery case
    • (Loose) 2x DE-9 bracket
    • (Loose) 2x DE-9 cables
    • (Bag) Tamiya E-match safeties
    • (Box) Tamiya connector set
    • (Loose) 4x Module spacers
    • (Bag) Blue Loctite
    • (Loose) Tweaker screwdriver
  • (Box) COTS electronics box
    • (Bag) 2x RRC3
    • (Bag) Big Red Bee
      • BRB PCB
      • 3700mAh EEMB battery
      • 2x BRB programmer
      • 2x JST-BRB adapter
    • (Loose) 433MHz whip antenna
    • (Loose) 2x RRC3 battery
    • (Bag) RRC3 accessories
      • RRC3 LCD
      • RRC3 Dongle
    • (Bag) Wiring
      • 2x XT-30 to ferrule
      • 2x Bridged breakouts
      • 2x arming key
    • (Loose) 2x 2S USB balance chargers
    • (Loose) 1x 1S USB charger
    • (Loose) Length of 8-conductor cable
    • (Loose) Length of large heat shrinke
    • Extra XT30 Connectors
    • Screwdriver
  • (Pelican case) Backup avionics hardware case
    • 2x RRC3
    • 2x RRC2L
    • 2x Big Red Bee
    • 1x EEMB 3700mAh battery
    • 2x RRC3 battery
    • 4x Fingertech screw switches (bag)
    • 2x DE-9 connector
    • 2x DE-9 breakout
    • Length of white 22AWG wire
    • Length of large heat shrink
  • (Bag) Spare 22AWG 8-conductor bulk cable
  • (Loose item) PROMPT pressure tube
  • (Soft case) Driver kit
  • (Box) Multimeter
  • (Bag) Multimeter leads set
  • (Soft case) General crimp kit
    • Crimp tool
    • Open-barrel crimping anvil
• Ground Station Aaron Chan (RIT Student) 
  • 2x batteries + barrel jack cables
  • Router 
  • Switch
  • 5x ethernet cable
  • Keyboard
• Toolbox (NOT ASSIGNED YET)
  • Driver kit
  • Needle-nose pliers
  • Wire stripper
  • Kapton tape
  • Electrical tape
  • Solder
  • Spade connector set
  • Heat shrink set
  • Flush cutters
  • Diagonal cutters
  • Larger screwdrivers
• Backplane remainders 
  • Backplane x3 
  • Unpopulated autopilot module x5
  • Sensor module x3
  • Power module x3
• Additional RF hardware Yevgeniy Gorbachev (RIT Student) 
  • 900 MHz antenna
  • 2x BNC to SMA cables (Arrow Yagi)
  • 2x N-type to SMA cables (900MHz Yagi, smaller 400MHz Yagi)
• Standalone backplane set 1 Aaron Chan (RIT Student) 
  • Dev module
  • Backplane
  • Power module
  • Sensor module
  • 2x Radio module
  • SwitchBlox
  • Backplane Battery Box
    • Balanced Charger
    • Battery
    • XT-60 TO Ferrule Adapter
  • PROMPT
• Standalone backplane set 2 Yevgeniy Gorbachev (RIT Student) 
  • Dev module
  • Backplane
  • Power module
  • Sensor module
  • Radio module
  • SwitchBlox