This Confluence space has been migrated and is no longer current. The content on this space will no longer be accessible after July 1, 2026.
Break Action Items
Subteam | Action Items | Assignees |
|---|---|---|
Admin | Set up meetings | @Alex Speyer (RIT Student) |
Complete 2nd Update | All Hands | |
Begin Technical Report | @Alex Speyer (RIT Student) @Yevgeniy Gorbachev (RIT Student) | |
Pay Entrance Fee | @Alex Speyer (RIT Student) | |
| ||
Structures | Get grace filament for testing | @Alex Durand (RIT Student) |
Begin writing up process for nosecone layup | @Alex Durand (RIT Student) | |
Look into CF weave options | @Alex Durand (RIT Student) | |
Update CAD to reflect Open Rocket | @Jake Halpern (RIT Student) | |
| ||
| ||
Analysis | Update Tensile Testing Document | @William Beckson (RIT Student) |
Bulkheads FEA | @William Beckson (RIT Student) | |
Boat tail FEA | @William Beckson (RIT Student) | |
RASAero Model | @William Beckson (RIT Student) | |
Start writing summaries for tech paper | @William Beckson (RIT Student) | |
| ||
| ||
| ||
| ||
Avionics | Plastics research | @Donovan Barros (RIT Student) |
Figure out Wiring Harness | @Aaron Chan (RIT Student) | |
Look into using all 1/4 inch Delrin | ?@Donovan Barros (RIT Student)? | |
| ||
| ||
| ||
| ||
Backplane | Test and debug W25Q software | @Aaron Chan (RIT Student) |
Test and debug BMP software | @Aaron Chan (RIT Student) | |
Test and debug LED software | @Aaron Chan (RIT Student) | |
Test and debug MS5607 ADXL software | @Akhil Devarapalli (RIT Student) | |
Backplane Schematic | @Billy Siegener (RIT Student) (Deactivated) | |
Autopilot Schematic | @Ben Hyman (RIT Student) | |
Power Schematic | @James May (RIT Student) | |
Radio Schematic | @Dante Sivo (RIT Student) | |
Sensor Schematic | @Louis Fleisher (RIT Student) @Mary Dertinger (RIT Student) | |
Payload | Find speed payload needs to fall |
|
Find snatch force at 150 ft/s | @Grace Dertinger (RIT Alumni) | |
Update BOM | @Louis Fleisher (RIT Student) | |
Finish airbrake CAD - with and without loadcell, make sure antenna fits | @Grace Dertinger (RIT Alumni) @Mary Dertinger (RIT Student) @Jonah Gimmi (RIT Student) | |
Spec load cell | @Grace Dertinger (RIT Alumni) | |
Determine streamer length chute |
| |
Run FEA |
| |
Component Selection | @Louis Fleisher (RIT Student) | |
AV bay layout | @Mary Dertinger (RIT Student) @Jonah Gimmi (RIT Student) | |
AV bay CAD | @Mary Dertinger (RIT Student) @Jonah Gimmi (RIT Student) @Riley Quinn (RIT Student) | |
Footprint and schematic for SCRAP | @Jim Heaney (RIT Student) | |
Reaction Wheel | Fix integration Issue | John Ye |
Separate Magnetic sensor and encoder | John Ye | |
Make new board | John Ye | |
Change software of new board | John Ye | |
| ||
| ||
| ||
Recovery | make sure all components arrive | @James May (RIT Student) |
Determine preliminary layout | @James May (RIT Student) | |
Conduct tender descender test | @James May (RIT Student) | |
Update OR recovery component weights | @James May (RIT Student) | |
Locate viable flame blanket | @James May (RIT Student) | |
Begin FDR slides | @James May (RIT Student) | |
| ||
Other | make video challenge script | @William Beckson (RIT Student) |
| ||
| ||
|